Army height and weight chart replaced by a max waist chart
Under the old Army Body Composition Program, Soldiers were first screened against a table of maximum weights by height, age and sex, and taped for body fat if they were over. Since 7 July 2026 there is no weight table. The standard is a waist-to-height ratio below 0.55, the same for everyone. The chart below turns that into the waist each height has to stay under.
| Height | Inches | Fails at (in) | Largest passing, 1/4 in | Fails at (cm) |
|---|---|---|---|---|
| 4'10" | 58 | 31.90 | 31.75 | 81.0 |
| 4'11" | 59 | 32.45 | 32.25 | 82.4 |
| 5'0" | 60 | 33.00 | 32.75 | 83.8 |
| 5'1" | 61 | 33.55 | 33.50 | 85.2 |
| 5'2" | 62 | 34.10 | 34.00 | 86.6 |
| 5'3" | 63 | 34.65 | 34.50 | 88.0 |
| 5'4" | 64 | 35.20 | 35.00 | 89.4 |
| 5'5" | 65 | 35.75 | 35.50 | 90.8 |
| 5'6" | 66 | 36.30 | 36.25 | 92.2 |
| 5'7" | 67 | 36.85 | 36.75 | 93.6 |
| 5'8" | 68 | 37.40 | 37.25 | 95.0 |
| 5'9" | 69 | 37.95 | 37.75 | 96.4 |
| 5'10" | 70 | 38.50 | 38.25 | 97.8 |
| 5'11" | 71 | 39.05 | 39.00 | 99.2 |
| 6'0" | 72 | 39.60 | 39.50 | 100.6 |
| 6'1" | 73 | 40.15 | 40.00 | 102.0 |
| 6'2" | 74 | 40.70 | 40.50 | 103.4 |
| 6'3" | 75 | 41.25 | 41.00 | 104.8 |
| 6'4" | 76 | 41.80 | 41.75 | 106.2 |
| 6'5" | 77 | 42.35 | 42.25 | 107.6 |
| 6'6" | 78 | 42.90 | 42.75 | 109.0 |
| 6'7" | 79 | 43.45 | 43.25 | 110.4 |
| 6'8" | 80 | 44.00 | 43.75 | 111.8 |
"Fails at" is height x 0.55, the waist that gives a ratio of exactly 0.550. Any waist below it passes, because the Army truncates the ratio to three decimals instead of rounding. The quarter-inch column is the largest tape reading in 1/4 inch steps that still passes.
How to use the waist-to-height standard
Measure your height in inches and your waist at the navel in inches, then divide waist by height. A result of 0.549 or lower meets the standard. To check the other way round, multiply your height by 0.55: your waist has to be smaller than that. TheArmy body fat calculator does the division and shows how much room you have.
What changed from the old height and weight tables
- No weight limit. Body weight is not part of the standard.
- No age or sex columns. One ratio for every Soldier and cadet.
- No tape test as a second step. All previous body fat methods are rescinded, and you cannot request one to challenge a WHtR result.
- No AFT exemption. The 465-point AFT exemption was rescinded.
- Twice a year. Every Soldier is screened at least twice per calendar year, at least seven days apart from an AFT or CFT.
Frequently asked questions
Does the Army still use height and weight tables?
No. The Army FAQ for Army Directive 2026-13 says the waist-to-height ratio screening replaces the height and weight tables previously used to screen Soldiers. Being over a table weight no longer triggers anything on its own.
What is the maximum waist for my height in the Army?
Multiply your height in inches by 0.55. Your waist at the navel must be below that number. At 5'9" (69 inches) the limit is 37.95 inches, so 37.75 passes and 38 fails.
Is the standard different for men and women or by age?
No. The 0.55 waist-to-height ratio is the same for every Soldier. The old height and weight tables and body fat limits had separate columns by sex and age; the new standard does not.
Does this apply to enlisting at MEPS?
This page covers the Army Body Composition Program for Soldiers already serving, plus USMA and Senior ROTC cadets. Enlistment screening at MEPS follows separate Department of Defense accession rules, so confirm current entry standards with your recruiter.